Binders / Chemicals
In-house developed systems for stone carpets and pebble coatings.
Here you will find everything from the substrate to care: primers, waterproofing, binders, pore fillers as well as smoothing aid, cleaners and moss remover under Other. A good binder needs only 4 % of the stone weight – the more a product needs, the lower its bonding strength usually is.
S042-25 2K Epoxy Mortar Resin (Quick-drying resin after approximately 4 hours) For mixing with quartz sand for resin screed. (Add 10 - 15 % to the weight of the quartz sand) Also very suitable as a primer with sand sprinkling.Container size: 25 kgPlease pay attention to the processing instructions on the data sheets.
S1000 is a 2K epoxy primer, also used as mortar resin.After priming, sprinkle with quartz sand.Fast dryingGood leveling and filling propertiesGood flowabilityRemain flexibleNo primer required (with 2-coat application)Solvent-free, dimensionally stable, and odorlessChemical resistant, resistant to plasticizersTotal container size: 25 kg
S102 is a 1K rapid primer for rolling,dry to the touch after about 30 minutes at 20 °C.Sufficient for approximately 30 m² (undiluted).Can be diluted with water 1:1 for double the coverage,but with a longer drying time.Universal primer for absorbent and non-absorbent substrates,as well as for smooth and rough surfaces, suitable for both interior and exterior use.Stir before use, as the quartz sand settles at the bottom of the bucket.Can be diluted with water for highly absorbent substrates.Comes in a 5 kg bucket.
S140 Application:Component A is at the bottom, and Component B is in the lid insert. Pierce the lid insert and then remove it, and mix both components well.Please follow the processing instructions on our downloadable data sheets.For the instructions and product data sheets:https://www.steinsystem.com/index.php?id=5Video on application:[Steinteppich Verarbeitung - YouTube](Steinteppich Verarbeitung - YouTube)
S140 Application:Component A is at the bottom, and Component B is in the lid insert.Pierce the lid insert and then remove it, and mix both components well.Please follow the processing instructions on our downloadable data sheets.For the instructions and product data sheets:https://www.steinsystem.com/index.php?id=5Video on application:[Steinteppich Verarbeitung - YouTube](Steinteppich Verarbeitung - YouTube)
The 1K acrylic pore filler is used to close small pores between the stones and is applied to a completely dry surface using a foam rubber trowel or rubber squeegee.Consumption for grain size 2 - 4 mm: approx. 1 - 1.5 kg per m²Consumption for grain size 4 - 8 mm: approx. 2 - 2.5 kg per m²The product initially has a gel-like, milky appearance and only becomes clear after approximately 1 - 2 days when fully dried.A second coat may only be applied after 48 hours.If the first layer is not completely clear, the second layer must not be applied.Our recommendation:After the first layer has fully dried, apply a second coat.Two thin layers are better than one thick layer and dry significantly faster.Walkable after just 6 hours.The stone texture remains visible after application, as the product sinks slightly.Available packaging sizes: 2.5 kg and 10 kgPlease follow the processing instructions provided in our customer login area.Login details are printed on the invoice or can be requested from us.
The 1K acrylic pore filler is used to close small pores between the stones and is applied to a completely dry surface using a foam rubber trowel or rubber squeegee.Consumption for grain size 2 - 4 mm: approx. 1 - 1.5 kg per m²Consumption for grain size 4 - 8 mm: approx. 2 - 2.5 kg per m²The product initially has a gel-like, milky appearance and only becomes clear after approximately 1 - 2 days when fully dried.A second coat may only be applied after 48 hours.If the first layer is not completely clear, the second layer must not be applied.Our recommendation:After the first layer has fully dried, apply a second coat.Two thin layers are better than one thick layer and dry significantly faster.Walkable after just 6 hours.The stone texture remains visible after application, as the product sinks slightly.Available packaging sizes: 2.5 kg and 10 kgPlease follow the processing instructions provided in our customer login area.Login details are printed on the invoice or can be requested from us.
The diverse product characteristics make the terrazzo filling compound a true all-round talent when it comes to grouting. The quartz sand-free special grout mortar based on cement is fine-grained and therefore perfect for stone carpets.Perfect for stone carpets, stoneware, stone stoneware, porcelain stoneware, glass mosaics, glass tiles, and all natural stones such as Carrara marble, travertine, granite, etc., the terracotta filling compound from SteinSystem is ideal. Thanks to its quick-setting and fast-hardening properties, you can walk on the filled area after just 3 hours. The pores are now waterproof and frost-resistant, making it suitable for both indoor and outdoor use. It is especially effective on demanding substrates, such as underfloor heating, and is frost- and weather-resistant.Mixing: Combine 5 kg of powder with 1 liter of sealing agent and 500 to 1000 ml of water, stirring well. This results in approximately 6.5 - 7kgof total mass. The amount of water added determines the fluid state, workability, and working time. Without water, the product is too thick and difficult to work with.Application: Use a foam rubber trowel to apply the filling compound into the pores, removing excess material. Optionally, you canre-smooth with a sponge board. Allow the filling compound to dry slightly, then smooth it with a damp sponge board using circular motions. Finally, wipe clean with a towel.For added shine, the surface can be rolled over with EP or PU after it has fully dried.If you have any questions, we are always happy to assist you.
The diverse product characteristics make the terrazzo filling compound a true all-round talent when it comes to grouting. The quartz sand-free special grout mortar based on cement is fine-grained and therefore perfect for stone carpets.Perfect for stone carpets, stoneware, stone stoneware, porcelain stoneware, glass mosaics, glass tiles, and all natural stones such as Carrara marble, travertine, granite, etc., the terracotta filling compound from SteinSystem is ideal. Thanks to its quick-setting and fast-hardening properties, you can walk on the filled area after just 3 hours. The pores are now waterproof and frost-resistant, making it suitable for both indoor and outdoor use. It is especially effective on demanding substrates, such as underfloor heating, and is frost- and weather-resistant.Mixing: Combine 5 kg of powder with 1 liter of sealing agent and 350 to 500 ml of water, stirring well. This results in approximately 6.5 kg of total mass. The amount of water added determines the fluid state, workability, and working time. Without water, the product is too thick and difficult to work with.Application: Use a foam rubber trowel to apply the filling compound into the pores, removing excess material. Optionally, you can re-smooth with a sponge board. Allow the filling compound to dry slightly, then smooth it with a damp sponge board using circular motions. Finally, wipe clean with a towel.For added shine, the surface can be rolled over with EP or PU after it has fully dried.If you have any questions, we are always happy to assist you.
The diverse product characteristics make the terrazzo filling compound a true all-round talent when it comes to grouting. The quartz sand-free special grout mortar based on cement is fine-grained and therefore perfect for stone carpets.Perfect for stone carpets, stoneware, stone stoneware, porcelain stoneware, glass mosaics, glass tiles, and all natural stones such as Carrara marble, travertine, granite, etc., the terracotta filling compound from SteinSystem is ideal. Thanks to its quick-setting and fast-hardening properties, you can walk on the filled area after just 3 hours. The pores are now waterproof and frost-resistant, making it suitable for both indoor and outdoor use. It is especially effective on demanding substrates, such as underfloor heating, and is frost- and weather-resistant.Mixing: Combine 5 kg of powder with 1 liter of sealing agent and 350 to 500 ml of water, stirring well. This results in approximately 6.5 kg of total mass. The amount of water added determines the fluid state, workability, and working time. Without water, the product is too thick and difficult to work with.Application: Use a foam rubber trowel to apply the filling compound into the pores, removing excess material. Optionally, you can re-smooth with a sponge board. Allow the filling compound to dry slightly, then smooth it with a damp sponge board using circular motions. Finally, wipe clean with a towel.For added shine, the surface can be rolled over with EP or PU after it has fully dried.If you have any questions, we are always happy to assist you.
The best liquid foil / seal made of 2K polyureaElasticity up to 800%For outdoor sealing, e. g. B. on balcony, terrace, external stairsConsumption approx. 1,5-2 kg/m2Very short potting time, only 8 minutes. We ask you to observe the processing instructions on our data sheets in the customer loginThe access data are on the invoice or can be requested from us. Delivery size 10 kgresults in a price per kg of 17,99 €Binders / adhesives / chemicals are not indefinitely durable, therefore these products should also be processed in a timely manner. You can find more information in the product data sheets, which can be requested from us.
Acceleration of drying time through the addition of S304-B,which can reduce the drying time from 12 - 24 hours to 1 - 3 hours.S304-B must be ordered separately when in use.- Solvent- and VOC-free- Can be applied with a roller- Bubble- and defect-free membrane- Suitable for application even at low temperatures- Excellent adhesion to almost all substrates, with or without the use of special primers- Cold-resistant: The film remains elastic even at temperatures as low as -40°C- Excellent mechanical properties, high tensile strength, high abrasion resistance- Water vapor permeableMinimum total consumption: approximately 1.5 kg/m² in one layer. with fleece reinforcement 3 kg/m² in one layer.Recoat time: 12 - 24 hoursShelf life: 12 months in the original sealed container when stored at +5°C to +25°C. Keep away from direct sunlight.
Special properties: Cures rapidly, remains flexible even at low temperatures, does not foam, even in high humidity.For smoothing, a smoothing aid S630-1 is recommended.Consumption as a binder: 1 - 1.25 kg per 25 kg of marble chips. (4 - 5% of the marble weight)Consumption as surface hardening: 200 - 250 g / m² (sufficient for 4 - 5 m²)Supplied in a 1-liter tin can.Binders / adhesives / chemicals are not indefinitely durable, so these products should be used promptly. Further details can be found in the product data sheets, which can be requested from us.Not suitable for parking areas for vehicles or equipment with rubber tires or plastics containing plasticizers, as plasticizer exchange could occur and marks/stains could be created.
Special properties: Cures rapidly, remains flexible even at low temperatures, does not foam, even in high humidity.For smoothing, a smoothing aid S630-1 is recommended.Consumption as a binder: 1 - 1.25 kg per 25 kg of marble chips. (4 - 5% of the marble weight)Consumption as surface hardening: 200 - 250 g / m² (sufficient for 4 - 5 m²)Supplied in a 4-liter tin can.Binders / adhesives / chemicals are not indefinitely durable, so these products should be used promptly. Further details can be found in the product data sheets, which can be requested from us.Not suitable for parking areas for vehicles or equipment with rubber tires or plastics containing plasticizers, as plasticizer exchange could occur and marks/stains could be created.
Special features: Best processing, easy smoothing, excellent result,Solvent-free, frost-resistant, UV-resistant, yellowing-resistant, slightly flexible,Optimal processing temperature 20°C ( +/- 5°C )Processing time at 20°C approximately 1 hour.Minimum shelf life 3 months from delivery dateConsumption: 1 kg per 25 kg of marble chips. ( 4 % of the marble weight )Incorrect application may result in foaming / blistering.Please pay attention to the instructions on the data sheets.
Special features: Best processing, easy smoothing, excellent result,Solvent-free, frost-resistant, UV-resistant, yellowing-resistant, slightly flexible,Optimal processing temperature 20°C ( +/- 5°C )Processing time at 20°C approximately 1 hour.Minimum shelf life 3 months from delivery dateConsumption: 1 kg per 25 kg of marble chips. ( 4 % of the marble weight )Incorrect application may result in foaming / blistering.Please pay attention to the instructions on the data sheets.
Areas of application: Base areas, on stair steps, or entire walls can be covered/coated with gravel coating / stone carpet.Solvent-free, frost-resistant, UV-resistant, yellowing-resistant, curing slightly milky/matte. To achieve a higher gloss, we recommend applying a surface hardener additionally.Consumption: approximately 11% of the stone weight, of which approximately 8% = 2 kg for 25 kg of stones and the remaining approximately 800 g to skim coat the wall. A layer approximately 1 mm thick is needed as an adhesive bridge. Thus, these 2.8 kg are sufficient for 25 kg of marble chips.Delivery: 2.8 kgShelf life: at least 10 months If stored beyond its shelf life, a skin may form on the top layer, which can be easily removed. Thus, the material underneath is often still usable.Further instructions can be found in the data sheets and instructions for download. Here: https://www.steinsystem.com/downloads/
By adding this thickening agent / thickening powder, the resin becomes so viscous that a stone carpet / marble gravel can be troweled onto vertical surfaces.Delivery scope: 1 x 1 kg thickening powder, sufficient to thicken 10 kg of resin.For best results, mix in a closed bucket through a hole in the lid to prevent the fine powder from dispersing.
By adding this adjuster, it can be nested on vertical surfaces. Add to 1 kg of binder 9-10% of substitute 90 -100 g) Delivery 100 g solvent powder in plastic bucket. / €14. 99 Sufficient for the addition of approx. 1 kg of binder.
Special cleaner for cleaning installation and assembly tools & thinner for the binder S316.Packaged in a 1-liter can with an extendable and resealable spout.Cleaning thinner, highly flammablePlease note the hazardous material warnings on the label.Please pay attention to the processing instructions on our data sheets in the customer login.
With this, the professional smoothens, resulting in a perfect outcome. Smoothing aid is an indispensable tool for laying stonecarpet - compatible with binders based on PU and EP. The good surface quality of a stone carpet is ensured only by a consistently clean and well-gliding trowel. The smoothing aid comes in a spray bottle for easy spraying or brushing onto the trowel. After every second to third operation, spray the trowel with smoothing aid (very thinly). The smoothing aid behaves chemically neutral to the binder and therefore is not involved in the curing process. Thus, no stones stick to the trowel, and the stonecarpet can be applied cleanly. The dry and clean trowel is moistened with the smoothing aid at short intervals. Care should be taken not to allow the smoothing aid to come into contact with the substrate to be coated.
With this, the professional smoothens, resulting in a perfect outcome.Smoothing aid is an indispensable tool for laying stonecarpet - compatible with binders based on PU and EP. The good surface quality of a stone carpet is ensured only by a consistently clean and well-gliding trowel. The smoothing aid comes in a spray bottle for easy spraying or brushing onto the trowel.After every second to third operation, spray the trowel with smoothing aid (very thinly). The smoothing aid behaves chemically neutral to the binder and therefore is not involved in the curing process.Thus, no stones stick to the trowel, and the stonecarpet can be applied cleanly. The dry and clean trowel is moistened with the smoothing aid at short intervals. Care should be taken not to allow the smoothing aid to come into contact with the substrate to be coated.
With this, the professional smoothens, resulting in a perfect outcome.Smoothing aid is an indispensable tool for laying stonecarpet - compatible with binders based on PU and EP. The good surface quality of a stone carpet is ensured only by a consistently clean and well-gliding trowel. The smoothing aid comes in a spray bottle for easy spraying or brushing onto the trowel.After every second to third operation, spray the trowel with smoothing aid (very thinly). The smoothing aid behaves chemically neutral to the binder and therefore is not involved in the curing process.Thus, no stones stick to the trowel, and the stonecarpet can be applied cleanly. The dry and clean trowel is moistened with the smoothing aid at short intervals. Care should be taken not to allow the smoothing aid to come into contact with the substrate to be coated.
This smoothes the professional. S630 prevents spinning on the smooth cell. Perfect result. Apply thin film to the smooth cell / spray.